- Shop Kits
- Shop Parts
- Gift Cards
- How-to Guides
- Commercial Facilities
HEAVY DUTY STEEL: 18% THICKER, 18% STRONGER
EZ Snap™ Covers are the strongest and thickest galvanized steel and epoxy powder coated covers on the market. Our product is 18% stronger because we use 18% thicker steel.
EZ Snap™ Covers snap right over 95% of all existing hot water baseboard heaters. EZ Snap™ Covers create a beautiful, modern, finished look in any room in a matter of minutes, without days of painstaking installation and mess. We know it sounds too easy, but it’s true. EZ Snap™ Covers are a one size fits all product requiring no power tools for installation. Best of all, no huge professional plumber or HVAC contractor bills to pay.
RUST...FORGET ABOUT IT!
Rust? Forget about it! Our 20-Gauge galvanized steel and epoxy powder coated covers are the thickest and strongest on the market and are GUARANTEED not to rust.
If custom lengths are needed, we cut them to the exact length at no additional cost. You just snap the covers over your existing baseboard heaters and slip on the end caps. It’s that simple!
FAST, FAST, FAST
Did I mention fast delivery? How about FedEx fast. Your EZ Snap™ Covers ship in 1-2 days. Travel time to Ohio, Michigan, and Pennsylvania takes 1 day. Chicago and East Coast 2 days. Rocky Mountains 3 days. West Coast 3-4 Days. Not fast enough for you? If you order by 11 am Eastern time, just call us and we will do everything we can to get it out the same day.
Steel can be sharp. Therefore, we invented and developed our new safe edge design. This eliminates any sharp hazards when handling of our product without the risk of scraping or cutting your hands during the installation process.
EZ Snap™ Covers have a lifetime warranty against rust. Our EZ Snap™ covers are made of 20-Gauge galvanized steel, the thickest in the industry, which is then epoxy powder coated and oven baked (our galvanized is mill finished, not painted). EZ Snap™ Covers have a lifetime warranty against rust to the original purchaser for as long as they own the property and the covers have not been modified or damaged in any way. If they rust, send them back and we will replace them.
BORN IN THE U.S.A.
EZ Snap™ Covers are made in Cleveland, Ohio. EZ Snap™ Covers are made with American hands, American steel and create American jobs. We are American and proud of it.
WE SUPPORT OUR TROOPS & FIRST RESPONDERS
We love our soldiers, veterans, and first responders. We proudly support:
• the Wounded Warrior Project https://www.woundedwarriorproject.org/
• Dogs on Deployment https://www.dogsondeployment.org/
• Tunnel to Towers Foundation https://www.t2t.org/
We support our U.S. Military no matter what. God bless our troops!
WE WILL NOT LET YOU FAIL
If you have any questions about measuring or ordering, please call or chat with one of our certified technicians who will walk you through the whole process. We can help you measure and even put your order in for you. You can text us pictures, fax, or email us. We’ll make all the decisions for you, it’s that easy. We will not let you fail.
OUR EXPERIENCE AND HISTORY
Having been in the remodeling business for over 25 years, we knew that there had to be a better way to fix old, ugly baseboard heaters. EZ Snap™ Covers are that better way. The bent, rusted, cheesy 1950’s look of the original manufacturing companies are gone and the neat, clean, stylish look of today is here. EZ Snap™ Covers are modern looking, and are made with 20-Gauge galvanized steel, the thickest cover on the market today, and epoxy powder coated. Our product is truly remarkable and we give a lifetime warranty against rusting.
Our mission is to deliver EZ Snap™ Covers to the world in the quickest, worry-free, and most cost effective manner that we can. We have designed them so they are so easy to install “do-it-yourselfers” can easily install our heater covers with no tools in most cases. In fact, we are so confident that you will absolutely love everything about our new EZ Snap™ Baseboard Heater Covers that we offer a money-back guarantee if you are not 100% satisfied with our product. If for any reason, within 60 days of receiving our covers, you don’t like them, just send them back and we will refund your money. Securely package them up as you received them, ship them back, and once we receive the product undamaged (in like-new condition), we’ll return your purchase price.
Gary Fratianne, Owner
EZ Snap™ Covers
1080 Bassett Rd, Unit D, Westlake, OH 44145
E-mail: Click To Email
Do you have questions or a suggestion for us?
Measure the height from the floor to the top of the metal wall plate.
Follow our guide for baseboard heater cover measurement:
Any baseboard larger than 7 3/8" (188 mm) will be compatible with our standard cover.
Any measurement greater than 9 3/8" (238 mm) will fit our tall cover.
Measure from the bottom of the finned tube heating element to the top of the metal wall plate,
A measurement of 5 1/2" to 6 3/4" (140 mm – 172 mm) will fit our standard cover.
A measurement of 7 1/2" to 8 3/4" (191 mm – 222 mm) will fit our tall cover.
Measure the distance from the wall or the metal wall plate attached to the wall, to the outside of the finned tube heating element.
Any measurement of less than 3 1/8" (76 mm) inches from the wall will fit our
Any measurement of less than 3 1/8" (76 mm) inches from the wall will fit our tall cover.
EZ Snap™ Wall Widgets are used when your old or existing wall back plate has been removed or if you have to hang your new cover 1 inch or higher to bring them up to a height that will fit our installation guidelines. Just measure your overall desired height, subtract 1", drill a hole, preferably in a stud and attach it to the wall with the included screw.
EZ Snap™ Floor Fidgets easily raise your new covers ¾ inch to compensate for any ¾ inch floor (wood, tile, or other) that has been installed any time since your baseboard heater was originally installed. May be used for any reason when the overall height has been shortened and the total height is less than 7-½ inches for standard height or 9-½ inches for the TALL height EZ Snap™ BaseBoard Covers. Just use the self-tapping screws to secure them to the top of your existing wallplate.
EZ Snap™ Wall Contraptions are used when your wall back plate has been completely removed. EZ Snap™ Wall Contraptions receives your EZ Snap™ BaseBoard Cover and keeps your aluminum fin tube from sagging. These completely replace your wall back plate. To install, slide up from the bottom and make sure the top is at your desired height. Screw to the wall, then bend the front finger up to hold the fin tube in place.
Measure from wall to wall and subtract ½ inch (to allow for wiggle room when installing your new covers.) The endcaps can be pulled or slid ½ inch outward on either end to fit your existing length requirements. Choose 2 flush to wall end caps.
Measure the overall length of the existing unit with ends attached then subtract ½ inch (to allow for wiggle room when installing your new covers.) The endcaps can be pulled or slid ½ inch outward on either end to fit your existing length requirements. Choose 2 Closed or Open-end caps.
Measure from the corner to the end of the unit with ends attached then subtract ½ inch (to allow for wiggle room when installing your new covers.) The endcaps can be pulled or slid ½ inch outward on either end to fit your existing length requirements. Choose 1 Closed or Open-end & 1 flush to wall end cap.
Measure the left side from corner A to corner B (see diagram). Then subtract 3 inches for the 90 degree inside corner, then subtract another ½ inch (to allow for wiggle room when installing your new covers.) Repeat for the right side if also wall to wall. You need to subtract a total of 3½ inches from each side that is wall to wall. Choose your end caps.
Measure the left side from the corner of the wall to the end of the unit with ends caps. Then subtract 3 inches for the 90 degree inside corner, then subtract another ½ inch (to allow for wiggle room when installing your new covers.) Repeat for the right side. You need to subtract a total of 3½ inches from both left and right sides. Choose your end caps.
L-Shaped outside radiators ending in the middle of the wall:
Measure from outside corner of the wall A to the end of the radiator unit with end caps attached B, then subtract ½" (to allow for wiggle room when installing your new covers.)
Measure from outside corner of the wall to the corner of the wall, then subtract 1/2" (to allow for wiggle room when installing your new covers.)
Left leg - measure from the corner out to the end of the radiator subtract 3" for the corner and ½ (to allow for wiggle room when installing your new covers.)
Center leg - measure from corner to corner and subtract 3" for each corner a total of 6"
Right leg - measure from the corner out to the end of the radiator subtract 3" for the corner and ½" (to allow for wiggle room when installing your new covers.).
We recommend that you order covers a little longer than normal and cut them on site, as there are many opportunities for mistakes in measuring and installation. By cutting on site you can fit and cut to fit. The covers can be cut with a good quality jigsaw and a fine metal cutting blade.
Now that you’ve learned how to measure baseboard heaters,
you’re ready to order.