When it comes to setting facilities up for private or professional use, overall safety and security is the key to success. So, as a business owner, it’s your responsibility to make this environment both safe for your workers and protected from potential loss. But while it’s easy to place most of your focus on installing new locks, you should also be paying attention to the building’s heating system. Whether it be commercial buildings, housing authority offices, or assisted living facilities, their old baseboard heater systems are a hazard that you’ll need to address. This is why you should invest in a lockdown baseboard radiator cover and the benefits it offers to your business.
One of the primary reasons why you should invest in a lockdown baseboard radiator cover is the overall peace of mind it can give you. In contrast to some residential models that simply slide on over the existing heater unit, lockdown baseboard heaters attach to the wall with screws after installation. This prevents the device itself from tampering and minimizes the risk of parts falling off or going missing. As such, you won’t need to worry about any unauthorized individuals handling the system.
Depending on the type of business you’re running, the law requires companies to adhere to local safety regulations when opening a new location. From mounting smoke and carbon monoxide detectors to placing handrails next to staircases, each of these changes is mandatory to maintain a good relationship with the local government. Failing to get your building up to code can result in expensive fines and even an official citation until you can complete the necessary renovations. So, by installing a lockdown heater cover, you’re checking one of these regulations off the list.
Because the lockdown baseboard heater cover is immovable until it’s uninstalled, it further reduces the risk of someone sustaining an injury in passing. Those casually walking by the unit are less likely to sustain scratches from loose parts, and even those who directly touch the cover won’t sustain burns from the direct heat source. This will cut down on workplace or assisted living accidents and prevent your business from suffering the repercussions.
Though issues with your old baseboard heater might be one of the furthest things from your mind when opening a new business location, these devices still pose a risk. Whether it be theft or an injury, quality baseboard heaters can mitigate the threats and preserve your investment. So, with these things in mind, we at EZ Snap™ Covers dedicate ourselves to providing the leading replacement baseboard radiator covers on the market. With our products, you can rest easy knowing that your building is prepared for anything.
1080 Bassett Rd Unit D
Westlake, OH 44145 USA
Phone:
866.740.0005
Fax:
888.717.9751
Email:
support@ezsnapcovers.com
© 2024 EZ Snap Covers.
Powered by Shopify
Measure the height from the floor to the top of the metal wall plate.
Follow our guide for baseboard heater cover measurement:
Any baseboard larger than 7 3/8" (188 mm) will be compatible with our standard cover.
Any measurement greater than 9 3/8" (238 mm) will fit our tall cover.
Measure from the bottom of the finned tube heating element to the top of the metal wall plate,
A measurement of 5 1/2" to 6 3/4" (140 mm – 172 mm) will fit our standard cover.
A measurement of 7 1/2" to 8 3/4" (191 mm – 222 mm) will fit our tall cover.
Measure the distance from the wall or the metal wall plate attached to the wall, to the outside of the finned tube heating element.
Any measurement of less than 3 1/8" (76 mm) inches from the wall will fit our
standard cover.
Any measurement of less than 3 1/8" (76 mm) inches from the wall will fit our tall cover.
EZ Snap™ Wall Widgets are used when your old or existing wall back plate has been removed or if you have to hang your new cover 1 inch or higher to bring them up to a height that will fit our installation guidelines. Just measure your overall desired height, subtract 1", drill a hole, preferably in a stud and attach it to the wall with the included screw.
EZ Snap™ Floor Fidgets easily raise your new covers ¾ inch to compensate for any ¾ inch floor (wood, tile, or other) that has been installed any time since your baseboard heater was originally installed. May be used for any reason when the overall height has been shortened and the total height is less than 7-½ inches for standard height or 9-½ inches for the TALL height EZ Snap™ BaseBoard Covers. Just use the self-tapping screws to secure them to the top of your existing wallplate.
EZ Snap™ Wall Contraptions are used when your wall back plate has been completely removed. EZ Snap™ Wall Contraptions receives your EZ Snap™ BaseBoard Cover and keeps your aluminum fin tube from sagging. These completely replace your wall back plate. To install, slide up from the bottom and make sure the top is at your desired height. Screw to the wall, then bend the front finger up to hold the fin tube in place.
Measure from wall to wall and subtract ½ inch (to allow for wiggle room when installing your new covers.) The endcaps can be pulled or slid ½ inch outward on either end to fit your existing length requirements. Choose 2 flush to wall end caps.
Measure the overall length of the existing unit with ends attached then subtract ½ inch (to allow for wiggle room when installing your new covers.) The endcaps can be pulled or slid ½ inch outward on either end to fit your existing length requirements. Choose 2 Closed or Open-end caps.
Measure from the corner to the end of the unit with ends attached then subtract ½ inch (to allow for wiggle room when installing your new covers.) The endcaps can be pulled or slid ½ inch outward on either end to fit your existing length requirements. Choose 1 Closed or Open-end & 1 flush to wall end cap.
Measure the left side from corner A to corner B (see diagram). Then subtract 3 inches for the 90 degree inside corner, then subtract another ½ inch (to allow for wiggle room when installing your new covers.) Repeat for the right side if also wall to wall. You need to subtract a total of 3½ inches from each side that is wall to wall. Choose your end caps.
Measure the left side from the corner of the wall to the end of the unit with ends caps. Then subtract 3 inches for the 90 degree inside corner, then subtract another ½ inch (to allow for wiggle room when installing your new covers.) Repeat for the right side. You need to subtract a total of 3½ inches from both left and right sides. Choose your end caps.
L-Shaped outside radiators ending in the middle of the wall:
Measure from outside corner of the wall A to the end of the radiator unit with end caps attached B, then subtract ½" (to allow for wiggle room when installing your new covers.)
Measure from outside corner of the wall to the corner of the wall, then subtract 1/2" (to allow for wiggle room when installing your new covers.)
Left leg - measure from the corner out to the end of the radiator subtract 3" for the corner and ½ (to allow for wiggle room when installing your new covers.)
Center leg - measure from corner to corner and subtract 3" for each corner a total of 6"
Right leg - measure from the corner out to the end of the radiator subtract 3" for the corner and ½" (to allow for wiggle room when installing your new covers.).
We recommend that you order covers a little longer than normal and cut them on site, as there are many opportunities for mistakes in measuring and installation. By cutting on site you can fit and cut to fit. The covers can be cut with a good quality jigsaw and a fine metal cutting blade.
Now that you’ve learned how to measure baseboard heaters,
you’re ready to order.